If a replacement eyeglass screw goes into the hole but never becomes snug, stop turning it. The problem is usually not solved by applying more force. A screw can appear to “fit” because its shaft enters the hinge or mount, yet still have the wrong thread, insufficient usable length, damaged threads, or a joint that is not aligned correctly.
The safest troubleshooting order is to remove the screw, inspect the joint, compare it with the original hardware if available, and test whether the screw begins threading smoothly by hand. If it spins freely without clamping, binds after only part of a turn, or needs force to continue, treat that as a mismatch or damaged-thread warning.
First Identify What “Won’t Tighten” Means
Different symptoms point to different causes.
The screw spins freely and never gets snug
This often means the threads are not engaging. Possible reasons include a screw that is too thin, a thread pitch mismatch, worn screw threads, or damaged threads in the hinge barrel or receiving component.
The screw starts, then becomes tight almost immediately
This can indicate cross-threading, the wrong thread pitch, dirt or damage in the receiving threads, or hinge holes that are not aligned.
The screw goes all the way in but the hinge is still loose
The screw may be too long in the wrong way, too short to clamp the joint, the hinge barrels may be worn, or the screw may not be seating under its head as intended.
The screw tightens, then loosens again
That is a different failure pattern. See Why Eyeglass Screws Keep Coming Loose for recurring loosening after an apparently successful installation.
A Hole Match Is Not a Thread Match
Tiny eyewear screws are selected by more than visible diameter. A useful match can depend on:
- Repair location
- Shaft diameter
- Thread pitch or thread form
- Head and drive style
- Usable length
- The receiving part inside the hinge, rim or nose-pad mount
A screw can pass through the upper hinge barrel yet fail to engage the threaded barrel below it. That is why “it fits through the hole” is not enough evidence that the hardware is correct.
The EBJDE Eyeglass Screw Size Guide explains the main dimensions to compare before installation.
Check Hinge Alignment Before Blaming the Screw
On a temple hinge, the barrels must line up before the screw can thread correctly.
Open the temple to a comfortable working angle and look through the screw channel under bright light. The barrel holes should form a clean path. If one barrel is shifted sideways, tilted or being pulled into position by the screw, the screw may enter at an angle and cross-thread.
Do not use the screw as a lever to force the barrels into alignment.
If the temple must be twisted hard to line up, the hinge or frame may be bent. A professional adjustment is safer than forcing a replacement screw through misaligned metal.
Compare With the Original Screw
If the original screw is available, compare it side by side with the replacement.
Look at:
- Overall length
- Threaded length
- Shaft diameter
- Thread spacing
- Head diameter
- Head shape
- Phillips, slotted or other drive style
- Any unthreaded shoulder or special tip
Two screws can look almost identical until they are placed next to each other. Small differences matter at eyewear scale.
If the original screw is missing, compare with the intact opposite hinge only as a reference. Do not assume both sides always use identical hardware on unusual or repaired frames.
Test the First Turns Without Force
A compatible screw should begin smoothly when the joint is correctly aligned.
Use a precision screwdriver that properly fills the screw head. Keep the driver straight and apply only enough downward pressure to prevent slipping.
Stop if:
- The screw tilts.
- The first turn feels gritty or unusually hard.
- The screw stops after a fraction of a turn.
- The driver starts damaging the slot.
- The hinge barrels spread apart as you turn.
- The screw spins without becoming more secure.
Backing out early can prevent a small mismatch from becoming stripped threads.
If the Screw Spins Freely
A freely spinning screw usually means the screw is not gripping useful threads.
Remove it and inspect the screw under bright light. Worn or flattened threads can prevent engagement. Then inspect the receiving hole as well as possible without inserting sharp improvised tools.
Try a properly matched replacement only if you can identify the correct size. If several correctly sized screws all spin without tightening, the receiving threads may be damaged.
A stripped hinge barrel is not fixed by forcing a larger screw into it. Upsizing a screw without knowing the hinge dimensions can permanently damage the joint.
If the Screw Binds After One or Two Turns
Binding early is a classic reason to stop.
Possible causes include:
- Wrong thread pitch
- Cross-threading
- Misaligned barrels
- Debris or corrosion in the threads
- A bent screw
- Damage from a previous forced repair
Remove the screw and check whether it started at an angle. Re-align the parts and try again only if the screw and receiving threads appear undamaged and the hardware has been positively matched.
If resistance returns in the same place, do not keep working the screw back and forth. That can remove more material from already delicate threads.
If the Screw Tightens but the Joint Is Still Loose
The screw can be “tight” without actually clamping the parts correctly.
Check whether:
- The screw head is seating against the intended surface.
- The threaded portion is long enough to engage the receiving threads.
- The hinge barrels have excessive wear.
- A washer, sleeve, nut or bushing is missing.
- The hardware belongs to a different type of mount.
Rimless and some specialty assemblies can use multiple small components. Missing one part can make a correctly threaded screw feel ineffective.
Do Not Fix a Thread Problem With More Torque
More torque is rarely the correct answer when a tiny replacement screw will not tighten.
Excess force can:
- Strip the screw head
- Strip the hinge threads
- Spread or crack a hinge barrel
- Scratch the frame
- Slip into the lens
- Damage rimless mounting holes
Use the smallest amount of force needed to confirm whether the hardware is engaging normally.
What About Threadlocker, Nail Polish or Glue?
Avoid using household adhesives or strong thread-locking products to compensate for a screw that does not actually fit or tighten.
A chemical locking product cannot repair mismatched threads, a stripped hinge barrel, missing hardware or a bent joint. It can also make later disassembly more difficult or create contact risks around frame finishes and lenses.
First establish that the mechanical fit is correct. If a correctly matched screw later has a recurring loosening problem, an optician can recommend an appropriate repair method for that frame.
When to Stop DIY Repair
Take the glasses to an optician or repair professional if:
- A correctly matched screw still spins freely.
- The receiving threads appear stripped.
- The hinge barrel is cracked, spread or distorted.
- The screw is stuck or broken inside the joint.
- A rimless lens mounting point is involved.
- The frame is high-value, delicate or unfamiliar.
- You cannot align the hinge without force.
A professional may have screw gauges, taps, extraction tools and replacement hardware that are not practical for a one-off home repair.
FAQ
Why does my replacement screw go in but keep spinning?
The screw may be too thin, have the wrong thread pitch, have worn threads, or be entering a receiving hole whose threads are stripped.
Can I use a slightly larger screw?
Do not force a larger screw into an eyewear hinge. It can cut or damage the existing threads and make the repair harder.
How do I know if the hinge threads are stripped?
One warning sign is that multiple correctly matched screws spin without becoming snug. Confirmation is best done by an optician using appropriate tools.
What if the screw starts crooked?
Back it out immediately. Re-align the hinge barrels before trying again.
Can a screw be too short even if it looks correct?
Yes. A screw may enter the joint but fail to engage enough receiving thread to clamp the assembly.
Do I need a special screwdriver?
Use a precision driver that properly fits the screw head. An undersized or oversized tip can slip and damage the slot.
Match the Hardware Before You Tighten
A replacement eyeglass screw should not need persuasion. If the joint is aligned and the screw is the correct type, the first turns should feel controlled and the joint should become secure without excessive force.
Use the Eyeglass Screw Size Guide to compare replacement hardware, and browse EBJDE Eyeglass Repair Tools for precision screwdrivers, tweezers and other small-frame repair tools. If the receiving threads are damaged, stop before turning a simple screw replacement into a damaged hinge.
Recommended Eyewear Accessories
Metal Replacement Temple Arms for Eyeglasses | EBJDE - Black
- $9.99
- Unit price
- / per
-
Black
-
Coffee
-
Gold
-
Silver
- BlueRose GoldGun
Soft Eyeglass Ear Cushions & Anti-Slip Temple Sleeves | EBJDE - Black, 3-Pack
- $9.99
$15.99- $9.99
- Unit price
- / per
-
Black, 3-Pack
-
Pink, 3-Pack
-
Gray, 3-Pack
-
Purple, 3-Pack
- Dark Blue, 3-PackBrown, 3-PackBlack / Pink / Purple, 2-PackBlack / Brown / Gray, 2-PackBlack / Blue / Gray, 2-Pack
1mm Silicone Eyeglass Temple End Tips for Thin Metal Frames – 5 Pieces | EBJDE - Black, 5-Pack
- $9.99
- Unit price
- / per
-
Black, 5-Pack
-
White, 5-Pack
-
Brown, 5-Pack
-
Blue, 5-Pack
- Red, 5-PackPurple, 5-Pack
Silicone Push-In Replacement Nose Pads Compatible with Nike Eyeglasses | EBJDE - Black, 5 Pairs
- $9.99
- Unit price
- / per
-
Black, 5 Pairs
-
Gray, 5 Pairs
-
White, 5 Pairs
Long Silicone Temple-Tip Covers for Thin Metal Frames - Black
- $9.98
- Unit price
- / per
-
Black
-
White
-
Pink
-
Gray
- Light PurpleSky BlueOff-White
2×1mm Silicone Temple End Tips for Thin Metal Eyeglasses, 5-Pack | EBJDE - Black, 5-Pack
- $9.99
- Unit price
- / per
-
Black, 5-Pack
-
White, 5-Pack
-
Blue, 5-Pack
-
Brown, 5-Pack
- Red, 5-Pack






